Oh no! Where's the JavaScript?
Your Web browser does not have JavaScript enabled or does not support JavaScript. Please enable JavaScript on your Web browser to properly view this Web site, or upgrade to a Web browser that does support JavaScript.

LVD bending machines Error Codes

Last updated on 25 days ago
C
caaSuper Admin
Posted 25 days ago
LVD bending machines typically have a variety of error codes that may appear due to issues in the hydraulic, electrical, or software systems. Here’s a list of common error codes and solutions:

### 1. **Error E01: Hydraulic Pressure Failure**
- **Cause:** Insufficient hydraulic pressure.
- **Solution:**
- Check the hydraulic oil level and refill if low.
- Inspect for any leaks in the hydraulic lines.
- Ensure all connections are secure, and the hydraulic pump is functioning correctly.

### 2. **Error E02: Motor Overload**
- **Cause:** Motor overload due to excessive load or obstruction.
- **Solution:**
- Verify the load and ensure it’s within the machine’s capacity.
- Check for obstructions or mechanical resistance in the system.
- Allow the motor to cool down before restarting.

### 3. **Error E05: Backgauge Malfunction**
- **Cause:** The backgauge is not responding or is misaligned.
- **Solution:**
- Inspect the backgauge alignment and recalibrate if necessary.
- Check the backgauge motor and connections for issues.
- Clear any debris or obstacles that may be blocking movement.
C
caaSuper Admin
Posted 25 days ago
### 4. **Error E07: Axis Limit Exceeded**
- **Cause:** Axis has moved beyond its programmed limit.
- **Solution:**
- Verify the programmed parameters and ensure they are within safe limits.
- Reinitialize or reset the axis to bring it back within the operational range.
- Check for encoder or sensor malfunctions.

### 5. **Error E09: Safety Circuit Activated**
- **Cause:** Safety devices like guards or emergency stops have been activated.
- **Solution:**
- Inspect all safety devices and reset any that have been triggered.
- Check for any obstructions around the safety guards.
- Verify the integrity of the safety circuits.

### 6. **Error E12: Control System Error**
- **Cause:** Problem with the main control system.
- **Solution:**
- Restart the control system.
- Update the software or reflash if the error persists.
- Contact LVD support for further diagnostics if necessary.

### 7. **Error E15: Calibration Error**
- **Cause:** Misalignment or calibration issue with one of the axes.
- **Solution:**
- Run the calibration procedure as recommended by LVD.
- Inspect sensors and encoders on the affected axis.
- Ensure the machine is set up on a stable, level surface.
C
caaSuper Admin
Posted 25 days ago
### 8. **Error E20: Overtemperature Fault**
- **Cause:** Excessive temperature detected in the machine components.
- **Solution:**
- Check for adequate cooling and ensure fans are working.
- Inspect ventilation for blockages and clean as needed.
- Allow the machine to cool down before resuming operation.

### 9. **Error E25: Communication Fault**
- **Cause:** Communication issue between the control panel and other machine components.
- **Solution:**
- Check all cable connections between the controller and components.
- Restart the machine to reset communication channels.
- Replace or repair damaged cables if needed.

### 10. **Error E30: Memory/Storage Failure**
- **Cause:** Issues with the machine’s internal memory or storage.
- **Solution:**
- Clear unnecessary files to free up storage.
- Reinstall software if corruption is suspected.
- Consult LVD support for assistance with memory-related issues.

Always consult the specific manual or documentation for your LVD bending machine model for precise troubleshooting steps, as error codes can vary by model.
You can view all discussion threads in this forum.
You cannot start a new discussion thread in this forum.
You cannot reply in this discussion thread.
You cannot start on a poll in this forum.
You cannot upload attachments in this forum.
You cannot download attachments in this forum.
Sign In
Not a member yet? Click here to register.
Forgot Password?
Users Online Now
Guests Online 2
Members Online 0

Total Members: 11
Newest Member: Jhilam