23-11-2019, 12:03 PM
GSM GATE OPENER to open and close your gate (or any other electrical devices) from your phone
![[Image: 1.JPG]](https://1.bp.blogspot.com/-MX1fqWx3jcI/XdkfnJxdpLI/AAAAAAAAAnU/uFPrtdkp_ssAdgONB-DjukbzmxTClARqgCLcBGAsYHQ/s1600/1.JPG)
Open gate or garage door with a FREE call from your mobile phone
No more lost remote controls to replace
No more purchasing additional remotes for our family members or new employees.
No more batteries to replace in your remote controls.
![[Image: 2.JPG]](https://1.bp.blogspot.com/-Rx2itsR89tE/XdkfnKkPx3I/AAAAAAAAAnY/AYqMHACM3tw8MZZkVN0yYe02dnY4DxMMQCLcBGAsYHQ/s1600/2.JPG)
GSM Gate Opener RTU5015 is a very simple device which can be used for authorized door access, controlling gates, car parking systems. Just dial from Authorized User number then the Barrier and doors are opened, or the machine are turn on or off by the GSM Gate Opener. There are no call costs, the GSM Gate Opener rejects the call from authorized number then carries out the turn ON/OFF action
GSM Operator configurations
The default Password is 1234.
All the settings are through SMS commands, please edit the below SMS commands in your cellphone, then send to the RTU5015 Unit
You can program the GSM Gate Opener with SMS commands using your phone. The instruction to program the unit is given in the next page
GSM Operator Commands
![[Image: 3.JPG]](https://1.bp.blogspot.com/-I_nTxTUmIfo/XdkfnII_3NI/AAAAAAAAAnc/gXHG-gUD1ZYW-go83HBJ2YPS60P1489UACLcBGAsYHQ/s1600/3.JPG)
If you want to reset the RTU5015 to factory default, then please send RESET to it within 3
minutes after switch on the RTU5015.(The GSM Led in RED status, if the GSM LED change to GREEN, then the RTU5015 can not respond this command.)
Please note that the messages are chargeable for installing the module.
While setting the Relay 1 close time (door open) The time should be in 0 - 9.5 seconds. This command is useful in case you need to keep the relay closed (or button pressed) longer. The default time is 0.5 seconds (500 ms). You can change it with the GOT command.
The relay closed time is twice as the number you set, e.g.: if you set passwordd#GOT19#, means the relay closed time is 19/2=9.5Seconds. That means, you can keep the both relays closed (for opening and closing of door) for a maximum time of 9.5 seconds. Generally, one pulse is enough for motor driver to operate.
In some case, you may check the GSM signal quality, for which you should send password#CSQ? This command is useful to see the GSM network signal level of your GSM Gate Opener is receiving. After you send the command, you can receive a SMS with signal quality in range 0 to 32
Open gate or garage door with a FREE call from your mobile phone
No more lost remote controls to replace
No more purchasing additional remotes for our family members or new employees.
No more batteries to replace in your remote controls.
GSM Gate Opener RTU5015 is a very simple device which can be used for authorized door access, controlling gates, car parking systems. Just dial from Authorized User number then the Barrier and doors are opened, or the machine are turn on or off by the GSM Gate Opener. There are no call costs, the GSM Gate Opener rejects the call from authorized number then carries out the turn ON/OFF action
GSM Operator configurations
The default Password is 1234.
All the settings are through SMS commands, please edit the below SMS commands in your cellphone, then send to the RTU5015 Unit
You can program the GSM Gate Opener with SMS commands using your phone. The instruction to program the unit is given in the next page
GSM Operator Commands
If you want to reset the RTU5015 to factory default, then please send RESET to it within 3
minutes after switch on the RTU5015.(The GSM Led in RED status, if the GSM LED change to GREEN, then the RTU5015 can not respond this command.)
Please note that the messages are chargeable for installing the module.
While setting the Relay 1 close time (door open) The time should be in 0 - 9.5 seconds. This command is useful in case you need to keep the relay closed (or button pressed) longer. The default time is 0.5 seconds (500 ms). You can change it with the GOT command.
The relay closed time is twice as the number you set, e.g.: if you set passwordd#GOT19#, means the relay closed time is 19/2=9.5Seconds. That means, you can keep the both relays closed (for opening and closing of door) for a maximum time of 9.5 seconds. Generally, one pulse is enough for motor driver to operate.
In some case, you may check the GSM signal quality, for which you should send password#CSQ? This command is useful to see the GSM network signal level of your GSM Gate Opener is receiving. After you send the command, you can receive a SMS with signal quality in range 0 to 32